Ideal handling due to space-saving design and optimized foot constructionTransport with pallet truck or forklift: underride height 100mm / 3.94" with fork pocketsStable and safe welded constructionApproved for the storage of substances hazardous to waterWith nationwide valid declaration of conformity (ÜHP) according to StawaRLeak test with factory test certificateThe removable grating is hot-dip galvanized and serves as a levelling element

An IBC heating mat is used to heat filling material by heating the mat between the IBC pallet and the inner container. However, as a cheaper alternative to heating jackets, a heating mat is somewhat more complex to install.This IBC heating mat works by means of about 27m long, silicone-coated heating wires which are aluminum-laminated on both sides. This results in optimal stability and heat distribution. The built-in thermostats prevent overheating. The control thermostat is used to heat the product to 60°C (ATTENTION: The surface temperature of the mat can be up to 90°C!) In case of malfunction or failure of the control thermostat, the limiter thermostat controls the heating and limits the heating of the product to a maximum of 70°C. It should be noted, however, that the effective heat development of the product depends on several factors. First and foremost, the nature of the product must be taken into account in terms of its heat transfer coefficient. The ambient temperature and the pallet type of the IBC in question also play an important role. Container pallets with a steel tray (top surface / contact surface of the pallet with the IBC liner) are more suitable than wooden or plastic pallets, as these reflect / dissipate heat more strongly and thus absorb less. IMPORTANT NOTES: IBC tank heating mats may only be operated with filled IBCs! DO NOT undertake a "dry test". This could damage the IBC inner tank or even cause it to melt.The heating mat must be mounted between the IBC bladder and the pallet, never on the side or on top of the IBC. In order to remove the inner container of the IBC tank from the grid body, the cross struts on top must first be unscrewed. This usually requires unscrewing four screws on the top of the IBC. After unscrewing, the struts can be pulled out sideways and the IBC bladder can be pulled out upwards. Tip: To pull the bladder out of the lattice box without outside help, the IBC tank can also be laid on its side.The IBC heating mat is then placed on the pallet and the cable is run out to the side. Then the assembly takes place with insertion of the inner tank and screwing of the cross struts.The heating mat has a Euro plug and it is mandatory to operate it on a connection with a residual current circuit breaker of 30mA and a circuit breaker 10A.Be sure to read and follow the supplied instructions for proper operation of the heating mat. 

Ideal and stable elevation for your IBC!Made of galvanized steelIncluding grating as a footprintIdeal filling height for buckets, canisters, watering cans, etc.Suitable for 1x 1000L IBC (120x100 cm / 47.24x39.37") or smallerThe problem with the use of IBCs is usually only the filling from the container into another container.Especially during operation, the IBC valve at the bottom can be very obstructive. But also in the garden when filling a watering can.This IBC substructure solves the problem and can also be used for smaller containers. Due to the inserted grid, containers, barrels and other containers can be easily elevated and used.*Delivery does not include the IBC containers shown. Shown for illustrative purposes only.

This IBC drip pan made of high-quality PE is used when it is necessary to safely collect water-polluting substances and to store hazardous substances in an environmentally friendly, professional and safe manner.Corrosive, flammable, explosive, oxidizing or toxic hazardous substances must be handled and stored with special care - an important topic in every company!Especially in the area of IBC containers, solid solutions with an optimal price-performance ratio are required. This is what drip pans made of PE plastic offer.If filling and sampling have to be carried out directly at the IBC, a filling attachment at the IBC drip pan must not be dispensed with. This avoids unnecessary and possibly dangerous puddles in front of the IBC.Made of high quality PEWith galvanized steel gridWith filling attachmentCollecting volume 1100LCan be driven under with forklift or pallet truck*Stackable into each other for transport*High chemical resistance*Transport only in empty condition!  

This IBC drip pan made of high-quality PE is used when it is necessary to safely collect water-polluting substances and to store hazardous substances in an environmentally friendly, professional and safe manner.Corrosive, flammable, explosive, oxidizing or toxic hazardous substances must be handled and stored with special care - an important topic in every company!Especially in the area of IBC containers, solid solutions with an optimal price-performance ratio are required. This is what drip pans made of PE plastic offer.Made of high quality PEWith galvanized steel gridCollecting volume 1100LCan be driven under with forklift or pallet truck*Stackable into each other for transport*High chemical resistance*Transport only in empty condition!

This hazardous materials depot is made of high quality polyethylene and is ideal for storing an IBC or palletized barrels. Due to the manufacturing of high quality PE, the depot has a high chemical resistance and can be used both indoors and outdoors. Further advantages of the hazardous material depot are:Lockable with a sturdy stainless steel bar lockIntegrated document pocket on the inside of the doorIntegrated forklift pockets for loading with a pallet or IBCSeparate, stable storage rackDoor opening angles up to 270° (single position) which can be locked in 90° incrementsCurved roof for optimized snow load support, with integrated rain gutter at the top of the door openingPossibility to mount an interior lightCable gland at the rear wall

Made of high quality PEWith galvanized steel grateCollecting volume 1100l (1 IBC)Load capacity 3000kg (2 IBC)Can be driven under with forklift or pallet truck*Stackable into each other for transport*High chemical resistance*Transport only in empty condition!

This heating jacket especially for IBC containers is suitable for heating filling media quickly to 50-70 °C. Especially for media in applications such as production, a quickly available and constant heat is produced by means of a thermostat (0-90 °C).The jacket is made of high quality black nylon fabric on the outside and a high temperature resistant layer of silicone coated glass fibre fabric on the inside.Due to the flexible length adjustment, the heating jacket is suitable for IBCs with a circumference of 4060 to 4310 mm.Alternatively, the heating jacket can be used to heat multiple drums.Notes:When using, the manufacturer's specification for the maximum media temperature for the particular IBC must be checked. all temperatures given are for orientation onlythe achievable temperatures depend on many variables, such as the ambient temperature, the supply voltage, the medium, the material of the drum, the drum size, whether an agitator is used, etc.

Ideal handling due to space-saving design and optimized foot constructionTransport with pallet truck or forklift: underride height 100mm / 3.94" with fork pocketsStable and safe welded constructionApproved for the storage of substances hazardous to waterWith nationwide valid declaration of conformity (ÜHP) according to StawaRLeak test with factory test certificateThe removable grating is hot-dip galvanized and serves as a levelling element

This CUBE diesel tank from CEMO in the Outdoor Basic 1.500L variant has a general technical approval (Z-40.21-510).A collection tray and an optical leakage indicator have been integrated into the tank. The tank also has a filling connection with a TW coupling including a limit switch. Further equipment features include a vent cap, the level indicator and a discharge line.The electric pump operates at 230V and supplies a high-quality automatic nozzle, which can be locked in place by a holder on the tank.The delivery is completely assembled and ready for use.Due to the hinged lid, the CUBE diesel tank is approved for outdoor installation.

Ideal handling due to space-saving design and optimized foot constructionTransport with pallet truck or forklift: underride height 100mm / 3.94" with fork pocketsStable and safe welded constructionApproved for the storage of substances hazardous to waterWith nationwide valid declaration of conformity (ÜHP) according to StawaRLeak test with factory test certificateThe removable grating is hot-dip galvanized and serves as a levelling element

Ideal handling due to space-saving design and optimized foot constructionTransport with pallet truck or forklift: underride height 100mm / 3.94" with fork pocketsStable and safe welded constructionApproved for the storage of substances hazardous to waterWith nationwide valid declaration of conformity (ÜHP) according to StawaRLeak test with factory test certificateThe removable grating is hot-dip galvanized and serves as a levelling element