Frequently Asked Questions (FAQ)
Do I have to empty the IBC container in winter?
YES! We generally recommend that you empty the IBC container in winter and unscrew all accessories!
If your IBC container has a flap valve, this should remain open during the winter.
Ball valves should be dried and then closed. There is a film of water between the ball and the gasket which can cause it to burst.
My valve on the IBC has a fine thread. What to do now?
In 90% of cases, IBC valves always have a coarse thread. However, if your outlet tap on the IBC container has a fine thread, you should check the following:
Is it a camlock valve?
The distinguishing feature of a Camlock valve is the very short fine thread (short thread length). The diameter of the valve tapers all around after the fine thread. The diameter then widens again.
Detailed information is available HERE
Why is inch not always inch? Everything about nominal diameter, threaded pipe, ...
Nominal diameter is the inner diameter of a pipe or hose line. The nominal diameter is also the size or connection dimension of a fitting.
The actual inside diameter often deviates by several millimetres. If you want to combine pipes from different manufacturers, make sure that the nominal diameter DN corresponds to the same DIN standard.
Find out more HERE
How many IBC containers can I stack?
The following values are specified by the manufacturer for new IBC tanks:
Static load (idle state of the IBC containers): max. 4 IBC
Dynamic load (pallet / IBC container is in motion):
Füllgut Dichte > 1,4: 1 IBC
Good density < 1,4: 2 IBC
Find out more HERE
Can I fit an adapter, hose connection, ... directly to the IBC inner tank?
No - Our Accessories (not IBC replacement valves!) are mounted on the standard IBC outlet tap, they are not designed for direct screw connection to the IBC inner tank.
Of course, there are also exceptional cases in which direct mounting on the inner container is possible, but we strongly advise against this!
Which pump for an IBC tank?
This is primarily dependent on the lid opening of the existing IBC. The IBC standard lid opening with DN150 is in most cases too small for submersible pumps, as the effective inside diameter is only around 14cm is concerned. Either a pressure pump (installation outside the IBC) or a drum pump with riser pipe should be used here.
With the larger IBC lid opening DN225 most submersible pumps can be lowered into the container and operated with a little skill.
How do I connect two IBC containers?
The easiest way is to use two IBC hose adapters and a suitable length of hose.
In most cases, however, a separate outlet / valve for water withdrawal is desired or the IBCs are to be stacked. There are significantly more details to consider here. We have summarized all the necessary information for you in our blog post: Blog
How many degrees can an IBC withstand?
Continuous temperature max. +40°C, filling temperature max. +60°C (applies to atmospheric pressure and water-like filling media).
IBC inner containers or bladders are made of HDPE (i.e. polyethylene), which begins to soften from +80°C. For this reason, IBC manufacturers guarantee the short-term stability of the inner container up to max. +60°C (e.g. during filling) and max. +40°C as a permanent temperature for storage / use (operating temperature)
Can IBC containers be placed in the ground?
No! IBC containers are not designed for this purpose and are therefore not suitable as underground cisterns
In principle, it is possible to install IBC containers underground, but only with great effort. When empty or not full, the inner containers themselves do not have sufficient stability or internal pressure to counteract the surrounding soil or filling material
Consequently, without a stable enclosure or retaining walls, the IBC will be crushed and very likely become unusable. It is also very difficult to use and maintain the IBC connections on the lid and valve.
A cistern designed for underground use is recommended here.
What doeas IBC Tank mean?What is an IBC Tank?
IBC stands for Intermediate Bulk Container and are stackable pallet containers for the transportation and storage of liquids or granular bulk goods.
The terms "IBC tank", "IBC container", "pallet tank" etc. are often used synonymously.
You can find out more in our Blog
Can full IBC containers be stacked?
YES, almost all IBCs can be stacked. Depending on the contents and IBC type, the rule of thumb is 4 IBCs upright (static) and 2 IBCs moving (dynamic).
Decisive factors are: Manufacturer's specifications, contents (density/weight), transportation or upright storage, IBC type (pallet, shape, etc.), condition of the IBC.
We explain what other details you should consider and what else there is to bear in mind in our Blogpost
What helps against algae in IBC containers?
Set up the IBC in the shade or provide shade (e.g. with IBC covers and sleeves) and at the same time pre-filter the water from the roof.
If there is already algae in the container, it must first be thoroughly removed. To do this, we recommend emptying and thoroughly cleaning the IBC tank (with suitable cleaning agents).
You can find out more about algae in IBCs in thisBlogpost
What size is an IBC container?
1000L IBC: 120x100x~116 cm LxWxH || 800L IBC: 120x100x~100 cm LxWxH || 800L IBC (EURO): 120x80x~118 cm LxWxH || 600L IBC: 120x80x~101 cm LxWxH || 300L IBC: 60x80x100 cm LxWxH
Depending on the manufacturer, pallet material and IBC type (UN, non-UN, food, etc.), there are differences in the height of the IBC.
Further technical information can be found in our Blog
Which stones under IBC containers?
Paving stones, planting rings or other concrete stones are best suited - anything that is stable, even and weatherproof.
Gas concrete blocks (often also called "Ytong blocks") or sandy / porous blocks, which absorb water and tend to crumble, are not suitable.
It is important for all variants to have an appropriately stable ground foundation on which the stones stand firmly and immovably (concrete, asphalt, paving, compacted gravel, etc.)
What IBC connections are there?
Connection to the IBC inner tank:
- S60x6 coarse thread
- S75x6 coarse thread
- S80x6 coarse thread
- S100x8 coarse thread
- Flange DN50 (e.g. WERIT**)
- Flange DN80 (e.g. WERIT**)
Connection to the IBC valve (outlet):
- S60x6 coarse thread
- S100x8 coarse thread
- 2" fine thread
- 2-1/8" fine thread + camlock